Tap any paragraph to write a margin note. Your notes collect in the Desk below the text and file under cases with @. The side-by-side margin rail opens on a larger screen.

§
Marginalia
Code · CFR · Title 40 — Protection of Environment · Part 60 · § 60.54

§ 60.54. Test methods and procedures.

745 words·~3 min read·/us/cfr/t40/s§ 60.54·

A research copy — for the controlling text, always check the official state or federal source. Not legal advice.

(a)In conducting the performance tests required in § 60.8, the owner or operator shall use as reference methods and procedures the test methods in appendix A of this part or other methods and procedures as specified in this section, except as provided in § 60.8(b).
(b)The owner or operator shall determine compliance with the particulate matter standard in § 60.52 as follows:
(1)The concentration
(c12)of particulate matter, corrected to 12 percent CO2, shall be computed for each run using the following equation: c12 = cs (12/%CO2) where: c12 = concentration of particulate matter, corrected to 12 percent CO2, g/dscm (gr/dscf). cs = concentration of particulate matter, g/dscm (gr/dscf). %CO2 = CO2 concentration, percent dry basis.
(2)Method 5 shall be used to determine the particulate matter concentration (cs). The sampling time and sample volume for each run shall be at least 60 minutes and 0.85 dscm (30 dscf).
(3)The emission rate correction factor, integrated or grab sampling and analysis procedure of Method 3B shall be used to determine CO2 concentration (%CO2).
(i)The CO2 sample shall be obtained simultaneously with, and at the same traverse points as, the particulate run. If the particulate run has more than 12 traverse points, the CO2 traverse points may be reduced to 12 if Method 1 is used to locate the 12 CO2 traverse points. If individual CO2 samples are taken at each traverse point, the CO2 concentration (%CO2) used in the correction equation shall be the arithmetic mean of the sample CO2 concentrations at all traverse points.
(ii)If sampling is conducted after a wet scrubber, an “adjusted” CO2 concentration [(%CO2)adj], which accounts for the effects of CO2 absorption and dilution air, may be used instead of the CO2 concentration determined in this paragraph. The adjusted CO2 concentration shall be determined by either of the procedures in paragraph
(c)of this section.
(c)The owner or operator may use either of the following procedures to determine the adjusted CO2 concentration.
(1)The volumetric flow rates at the inlet and outlet of the wet scrubber and the inlet CO2 concentration may be used to determine the adjusted CO2 concentration [(%CO2)adj] using the following equation: (%CO2)adj = (%CO2)di (Qdi/Qdo) where: (%CO2)adj = adjusted outlet CO2 concentration, percent dry basis. (%CO2)di = CO2 concentration measured before the scrubber, percent dry basis. Qdi = volumetric flow rate of effluent gas before the wet scrubber, dscm/min (dscf/min). Qdo = volumetric flow rate of effluent gas after the wet scrubber, dscm/min (dscf/min).
(i)At the outlet, Method 5 is used to determine the volumetric flow rate
(Qdo)of the effluent gas.
(ii)At the inlet, Method 2 is used to determine the volumetric flow rate
(Qdi)of the effluent gas as follows: Two full velocity traverses are conducted, one immediately before and one immediately after each particulate run conducted at the outlet, and the results are averaged.
(iii)At the inlet, the emission rate correction factor, integrated sampling and analysis procedure of Method 3B is used to determine the CO2 concentration [(%CO2)di] as follows: At least nine sampling points are selected randomly from the velocity traverse points and are divided randomly into three sets, equal in number of points; the first set of three or more points is used for the first run, the second set for the second run, and the third set for the third run. The CO2 sample is taken simultaneously with each particulate run being conducted at the outlet, by traversing the three sampling points (or more) and sampling at each point for equal increments of time.
(2)Excess air measurements may be used to determine the adjusted CO2 concentration [(%CO2)adj] using the following equation: (%CO2)adj = (%CO2)di [(100 + %EAi)/(100 + %EAo)] where: (%CO2)adj = adjusted outlet CO2 concentration, percent dry basis. (%CO2)di = CO2 concentration at the inlet of the wet scrubber, percent dry basis. %EAi = excess air at the inlet of the scrubber, percent. %EAo = excess air at the outlet of the scrubber, percent.
(i)A gas sample is collected as in paragraph (c)(1)(iii) of this section and the gas samples at both the inlet and outlet locations are analyzed for CO2, O2, and N2.
(ii)Equation 3B-3 of Method 3B is used to compute the percentages of excess air at the inlet and outlet of the wet scrubber. [54 FR 6665, Feb. 14, 1989, as amended at 55 FR 5212, Feb. 14, 1990; 65 FR 61753, Oct. 17, 2000]
Connections11 cite this
Citation graph
cites case law
§ 60.54
Test methods and procedures.
Fed. Reg.×6
C.F.R.×5
Cites 0Cited by 11 across 2 sources
★   the supreme law of the land   ★
Don't Tread on Me
E Pluribus Unum — out of many, one

"If you don't know your rights, you don't have any."

Marginalia · a citizen's law index
A research desk, not legal advice. Always read the cited source before relying on a summary.
Questions or an issue? support@self-law.org
disclaimerMarginalia is a research index, not a law firm. Nothing on this site is legal, tax, or financial advice and no attorney–client relationship is formed by using it. Statutes, regulations, and case law change; summaries, search results, AI output, and member posts may be incomplete, out of date, or wrong. Any interpretation drawn from material on this site should be validated by a licensed attorney in your jurisdiction before you act on it.