§ 1910.133. Eye and face protection.
658 words·~3 min read·
/us/cfr/t29/s§ 1910.133·A research copy — for the controlling text, always check the official state or federal source. Not legal advice.
(a)General requirements.
(1)The employer shall ensure that each affected employee uses appropriate eye or face protection when exposed to eye or face hazards from flying particles, molten metal, liquid chemicals, acids or caustic liquids, chemical gases or vapors, or potentially injurious light radiation.
(2)The employer shall ensure that each affected employee uses eye protection that provides side protection when there is a hazard from flying objects. Detachable side protectors (e.g. clip-on or slide-on side shields) meeting the pertinent requirements of this section are acceptable.
(3)The employer shall ensure that each affected employee who wears prescription lenses while engaged in operations that involve eye hazards wears eye protection that incorporates the prescription in its design, or wears eye protection that can be worn over the prescription lenses without disturbing the proper position of the prescription lenses or the protective lenses.
(4)Eye and face PPE shall be distinctly marked to facilitate identification of the manufacturer.
(5)The employer shall ensure that each affected employee uses equipment with filter lenses that have a shade number appropriate for the work being performed for protection from injurious light radiation. The following is a listing of appropriate shade numbers for various operations. ::: {width="100%"} ::: {.gpotbl_div} Filter Lenses for Protection Against Radiant Energy Operations Electrode Size 1/32 in. Arc Current Minimum\* Protective Shade Shielded metal arc welding Less than 3 Less than 60 7 3-5 60-160 8 5-8 160-250 10 More than 8 250-550 11 Gas metal arc welding and flux cored arc welding less than 60 7 60-160 10 160-250 10 250-500 10 Gas Tungsten arc welding less than 50 8 50-150 8 150-500 10 Air carbon (Light) less than 500 10 Arc cutting (Heavy) 500-1000 11 Plasma arc welding less than 20 6 20-100 8 100-400 10 400-800 11 Plasma arc cutting (light)\*\* less than 300 8 (medium)\*\* 300-400 9 (heavy)\*\* 400-800 10 Torch brazing 3 Torch soldering 2 Carbon arc welding 14 ::: ::: Filter Lenses for Protection Against Radiant Energy Operations Plate thickness---inches Plate thickness---mm Minimum\* Protective Shade Gas Welding: Light Under 1/8 Under 3.2 4 Medium 1/8 to 1/2 3.2 to 12.7 5 Heavy Over 1/2 Over 12.7 6 Oxygen cutting: Light Under 1 Under 25 3 Medium 1 to 6 25 to 150 4 Heavy Over 6 Over 150 5 ::: {.table_foot} - As a rule of thumb, start with a shade that is too dark to see the weld zone. Then go to a lighter shade which gives sufficient view of the weld zone without going below the minimum. In oxyfuel gas welding or cutting where the torch produces a high yellow light, it is desirable to use a filter lens that absorbs the yellow or sodium line in the visible light of the (spectrum) operation. \*\* These values apply where the actual arc is clearly seen. Experience has shown that lighter filters may be used when the arc is hidden by the workpiece. :::
(b)Criteria for protective eye and face protection.
(1)Protective eye and face protection devices must comply with any of the following consensus standards:
(i)ANSI/ISEA Z87.1-2010, Occupational and Educational Personal Eye and Face Protection Devices, incorporated by reference in § 1910.6;
(ii)ANSI Z87.1-2003, Occupational and Educational Personal Eye and Face Protection Devices, incorporated by reference in § 1910.6; or
(iii)ANSI Z87.1-1989 (R-1998), Practice for Occupational and Educational Eye and Face Protection, incorporated by reference in § 1910.6;
(2)Protective eye and face protection devices that the employer demonstrates are at least as effective as protective eye and face protection devices that are constructed in accordance with one of the above consensus standards will be deemed to be in compliance with the requirements of this section. \[59 FR 16360, Apr. 6, 1994; 59 FR 33911, July 1, 1994, as amended at 61 FR 9238, Mar. 7, 1996; 61 FR 19548, May 2, 1996; 74 FR 46356, Sept. 9, 2009; 81 FR 16090, Mar. 25, 2016\]
Connections64 cite this
Cited by 64 sections · top 37
CFR
register
- Rules and RegulationsNotice of proposed rulemaking (NPRM)
- Rules and RegulationsFinal rule
- NoticesRequest for public comments
- NoticesTemporary interim rule with request for comments
- NoticesProposed rule
- Rules and RegulationsNotice of proposed rulemaking and request for comments
- NoticesProposed rule
- Rules and RegulationsFinal rule
- Rules and RegulationsFinal rule
- Proposed RulesProposed rule
- Rules and RegulationsFinal rule
- Rules and RegulationsProposed rule
- Rules and RegulationsDEPARTMENT OF TRANSPORTATION
- Rules and RegulationsFinal rule
- Proposed RulesFinal rule; retrospective regulatory review (RRR)
- Rules and RegulationsProposed rule
- Rules and RegulationsFinal rule
- Rules and RegulationsProposed rule
- NoticesNotice of Availability of the Draft Environmental Impact Statement for the General Management Plan, Valley Forge National Historical Park
- Rules and RegulationsNotice of proposed rulemaking
- NoticesNotice of proposed rulemaking
- NoticesFinal rule
- Rules and RegulationsFinal rule
- NoticesFinal rule
- NoticesFinal rule
- NoticesNotice of proposed rule
- NoticesInterim final rule; request for comments
- Proposed RulesFinal rule
Citation graph
cites case law
§ 1910.133
Eye and face protection.
Fed. Reg.×55
C.F.R.×9
Cites 0Cited by 64 across 2 sources