§ 26.35. Changes to type certificates affecting fuel tank flammability.
1,053 words·~5 min read·
/us/cfr/t14/s§ 26.35·A research copy — for the controlling text, always check the official state or federal source. Not legal advice.
(a)Applicability. This section applies to holders and applicants for approvals of the following design changes to any airplane subject to 14 CFR 26.33(a):
(1)Any fuel tank designed to be Normally Emptied if the fuel tank installation was approved pursuant to a supplemental type certificate or a field approval before December 26, 2008;
(2)Any fuel tank designed to be Normally Emptied if an application for a supplemental type certificate or an amendment to a type certificate was made before December 26, 2008 and if the approval was not issued before December 26, 2008; and
(3)If an application for a supplemental type certificate or an amendment to a type certificate is made on or after December 26, 2008, any of the following design changes:
(i)Installation of a fuel tank designed to be Normally Emptied,
(ii)Changes to existing fuel tank capacity, or
(iii)Changes that may increase the flammability exposure of an existing fuel tank for which FRM or IMM is required by § 26.33(c).
(b)Flammability Exposure Analysis—(1) General. By the times specified in paragraphs (b)(1)(i) and (b)(1)(ii) of this section, each person subject to this section must submit for approval a flammability exposure analysis of the auxiliary fuel tanks or other affected fuel tanks, as defined in the type design, to the responsible Aircraft Certification Service office. This analysis must be conducted in accordance with Appendix N of part 25 of this chapter.
(i)Holders of supplemental type certificates and field approvals: Within 12 months of December 26, 2008,
(ii)Applicants for supplemental type certificates and for amendments to type certificates: Within 12 months after December 26, 2008, or before the certificate is issued, whichever occurs later.
(2)Exception. This paragraph does not apply to—
(i)Fuel tanks for which the type certificate holder, supplemental type certificate holder, or field approval holder has notified the FAA under paragraph
(f)of this section that it will provide design changes and service instructions for an IMM meeting the requirements of § 25.981(c) in effect December 26, 2008; and
(ii)Fuel tanks substantiated to be conventional unheated aluminum wing tanks.
(c)Impact Assessment. By the times specified in paragraphs (c)(1) and (c)(2) of this section, each person subject to paragraph (a)(1) of this section holding an approval for installation of a Normally Emptied fuel tank on an airplane model listed in Table 1 of this section, and each person subject to paragraph (a)(3)(iii) of this section, must submit for approval to the responsible Aircraft Certification Service office an assessment of the fuel tank system, as modified by their design change. The assessment must identify any features of the design change that compromise any critical design configuration control limitation (CDCCL) applicable to any airplane on which the design change is eligible for installation.
(1)Holders of supplemental type certificates and field approvals: Before June 26, 2011.
(2)Applicants for supplemental type certificates and for amendments to type certificates: Before June 26, 2011 or before the certificate is issued, whichever occurs later. Table 1 Model—Boeing 747 Series 737 Series 777 Series 767 Series 757 Series Model—Airbus A318, A319, A320, A321 Series A300, A310 Series A330, A340 Series
(d)Design Changes and Service Instructions. By the times specified in paragraph
(e)of this section, each person subject to this section must meet the requirements of paragraphs (d)(1) or (d)(2) of this section, as applicable.
(1)For holders and applicants subject to paragraph (a)(1) or (a)(3)(iii) of this section, if the assessment required by paragraph
(c)of this section identifies any features of the design change that compromise any CDCCL applicable to any airplane on which the design change is eligible for installation, the holder or applicant must submit for approval by the responsible Aircraft Certification Service office design changes and service instructions for Flammability Impact Mitigation Means
(FIMM)that would bring the design change into compliance with the CDCCL. Any fuel tank modified as required by this paragraph must also be evaluated as required by paragraph
(b)of this section.
(2)Applicants subject to paragraph (a)(2), or (a)(3)(i) of this section must comply with the requirements of 14 CFR 25.981, in effect on December 26, 2008.
(3)Applicants subject to paragraph (a)(3)(ii) of this section must comply with the requirements of 14 CFR 26.33.
(e)Compliance Times for Design Changes and Service Instructions. The following persons subject to this section must comply with the requirements of paragraph
(d)of this section at the specified times.
(1)Holders of supplemental type certificates and field approvals: Before December 26, 2012.
(2)Applicants for supplemental type certificates and for amendments to type certificates: Before December 26, 2012, or before the certificate is issued, whichever occurs later.
(f)Compliance Planning. By the applicable date specified in Table 2 of this section, each person subject to paragraph (a)(1) of this section must submit for approval by the responsible Aircraft Certification Service office compliance plans for the flammability exposure analysis required by paragraph
(b)of this section, the impact assessment required by paragraph
(c)of this section, and the design changes and service instructions required by paragraph
(d)of this section. Each person's compliance plans must include the following:
(1)A proposed project schedule for submitting the required analysis or impact assessment.
(2)A proposed means of compliance with paragraph
(d)of this section.
(3)For the requirements of paragraph
(d)of this section, a proposal for submitting a draft of all design changes, if any are required, and Airworthiness Limitations (including CDCCLs) for review by the responsible Aircraft Certification Service office not less than 60 days before the compliance time specified in paragraph
(e)of this section.
(4)For the requirements of paragraph
(d)of this section, a proposal for how the approved service information and any necessary modification parts will be made available to affected persons. Table 2—Compliance Planning Dates Flammability exposure analysis plan Impact assessment plan Design changes and service instructions plan STC and Field Approval HoldersMarch 26, 2009February 26, 2011August 26, 2011.
(g)Each person subject to this section must implement the compliance plans, or later revisions, as approved under paragraph
(f)of this section. [Doc. No. FAA-2005-22997, 73 FR 42499, July 21, 2008, as amended by Amdt. 26-3, 74 FR 31619, July 2, 2009; Doc. No. FAA-2018-0119, Amdt. 26-7, 83 FR 9170, Mar. 5, 2018]
Connections4 cite this · traces to 2
Cited by 4 sections
Citation graph
cites case law
§ 26.35
Changes to type certificates affecting fuel tank flammability.
C.F.R.×3
Fed. Reg.×1
Cites 2Cited by 4 across 2 sources