Rules and Regulations. Request for public comment on proposed collection of information

707 words·~3 min read·/register/2001/01/02/00-33412

A research copy — for the controlling text, always check the official state or federal source. Not legal advice.

BILLING CODE 4910-81-P DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration [Docket No. NHTSA-2000-8349] Reports, Forms, and Record Keeping Requirements AGENCY: National Highway Traffic Safety Administration (NHTSA), Department of Transportation. ACTION: Request for public comment on proposed collection of information. SUMMARY: Before a Federal agency can collect certain information from the public, it must receive approval from the Office of Management and Budget (OMB).

Under procedures established by the Paperwork Reduction Act of 1995, before seeking OMB approval, Federal agencies must solicit public comment on proposed collections of information, including extensions and reinstatement of previously approved collections. This document describes one collection of information for which NHTSA intends to seek OMB approval. DATES: Comments must be received on or before March 2, 2001. ADDRESSES: Comments must refer to the docket notice numbers cited at the beginning of this notice and be submitted to Docket Management, Room PL-401, 400 Seventh Street, SW., Washington, DC 20590.

Please identify the proposed collection of information for which a comment is provided, by referencing its OMB clearance Number. It is requested, but not required, that 2 copies of the comment be provided. The Docket Section is open on weekdays from 9 a.m. to 5 p.m. FOR FURTHER INFORMATION CONTACT: For further information, contact Edward Jettner, NHTSA, 400 Seventh Street, SW., Room 5320, NPS-11,Washington, DC 20590. Mr. Jettner's telephone number is

(202)366-4917. Please identify the relevant collection of information by referring to its OMB Control Number. SUPPLEMENTARY INFORMATION: Under the Paperwork Reduction Act of 1995, before an agency submits a proposed collection of information to OMB for approval, it must first publish a document in the **Federal Register** providing a 60-day comment period and otherwise consult with members of the public and affected agencies concerning each proposed collection of information. The OMB has promulgated regulations describing what must be included in such a document. Under OMB's regulation (at 5 CFR 1320.8(d)), an agency must ask for public comment on the following:

(i)whether the proposed collection of information is necessary for the proper performance of the functions of the agency, including whether the information will have practical utility;

(ii)the accuracy of the agency's estimate of the burden of the proposed collection of information, including the validity of the methodology and assumptions used;

(iii)how to enhance the quality, utility, and clarity of the information to be collected;

(iv)how to minimize the burden of the collection of information on those who are to respond, including the use of appropriate automated, electronic, mechanical, or other technological collection techniques or other forms of information technology, *e.g.* permitting electronic submission of responses. In compliance with these requirements, NHTSA asks for public comments on the following proposed collections of information: *Title:* Assigning DOT Code Numbers (Glazing Material Manufacturers). *OMB Control Number:* 2127-0038. *Affected Public:* Business or for-profit. *Abstract:* Title 49, Chapter 30115 of the U.S. Code specifies that the Secretary of Transportation shall require every manufacturer or distributor of a motor vehicle or motor vehicle equipment to furnish the distributor or dealer at the time of delivery certification that each item of motor vehicle equipment conforms to all applicable Federal Motor Vehicle Safety Standards (FMVSS). Using this authority, the agency issued FMVSS No. 571.205, “Glazing Materials”. This standard specifies requirements for glazing materials for use in passenger cars, multipurpose passenger vehicles, trucks, buses, motorcycles, slide-in campers and pickup covers designed to carry persons while in motion. Also, this standard specifies certification and marking of each piece of glazing materials. Certification for the items listed comes in the form of a label, tag or marking on the outside of the motor vehicle equipment and is permanently affixed and visible for the life of the motor vehicle equipment. The purpose of this standard is to aid in reducing injuries resulting from impact to glazing surfaces, and to ensure a necessary degree of transparency for driver visibility. Both glass and plastics are considered to be glazing materials which provide safety and minimize the possibility of occupants being thrown through the vehicle window in the event of a crash. *Estimated Annual Burden:* 11.5 hours. *Number of Respondents:* 23. Issued on: December 26, 2000. Stephen R. Kratzke, Associate Administrator for Safety Performance Standards. [FR Doc. 00-33412 Filed 12-29-00; 8:45 am]

Connections1 off-index

1 reference not yet in our index

5 CFR 1320.8(d)

Citation graph

cites case law

Rules and Regulations

Request for public comment on proposed collection of information

Cite5 CFR 1320.8(d)

Cites 1Cited by 0 across 0 sources