Unknown. Final rule
6,977 words·~32 min read·
/register/2013/09/17/2013-22574A research copy — for the controlling text, always check the official state or federal source. Not legal advice.
--- schema: federal-register doc_type: fedreg source_file: FR-2013-09-17.xml --- 78 180 Tuesday, September 17, 2013 Contents Actuaries, Joint Board for Enrollment See Joint Board for Enrollment of Actuaries Agency Health Agency for Healthcare Research and Quality NOTICES Agency Information Collection Activities; Proposals, Submissions, and Approvals, 57157-57159 2013-22578 Scientific Information Requests: Medication Therapy Management, 57159-57161 2013-22579 Agricultural Marketing Agricultural Marketing Service RULES United States Standards for Condition of Food Containers, 57033-57047 2013-22574 PROPOSED RULES Increased Assessment Rates:
Avocados Grown in South Florida, 57099-57101 2013-22539 Walnuts Grown in California, 57101-57104 2013-22571 Agriculture Agriculture Department See Agricultural Marketing Service See Food and Nutrition Service See Forest Service Army Army Department NOTICES Agency Information Collection Activities; Proposals, Submissions, and Approvals, 57133-57134 2013-22577 Meetings: Advisory Committee on Arlington National Cemetery, 57134 2013-22496 Census Bureau Census Bureau NOTICES Meetings:
Census Advisory Committees, 57128-57129 2013-22535 Centers Disease Centers for Disease Control and Prevention NOTICES Meetings: Community Preventive Services Task Force, 57161-57162 2013-22581 Centers Medicare Centers for Medicare & Medicaid Services NOTICES Agency Information Collection Activities; Proposals, Submissions, and Approvals, 57162-57164 2013-22515 2013-22516 Coast Guard Coast Guard RULES Special Local Regulations: Jacksonville Dragon Boat Festival; St. Johns River;
Jacksonville, FL, 57063-57066 2013-22596 Red Bull Flugtag Miami, Biscayne Bay; Miami, FL, 57061-57063 2013-22610 Commerce Commerce Department See Census Bureau See Economic Development Administration See International Trade Administration See National Oceanic and Atmospheric Administration Defense Department Defense Department See Army Department RULES Vet Center Services, 57067-57073 2013-22607 Drug Drug Enforcement Administration NOTICES Importers of Controlled Substances; Applications:
Cerilliant Corp., 57176-57177 2013-22536 Economic Development Economic Development Administration NOTICES Trade Adjustment Assistance; Petitions, 57129 2013-22543 Education Department Education Department RULES Final Waivers and Extensions of Project Periods: American Indian Vocational Rehabilitation Services Program, 57066-57067 2013-22626 NOTICES Agency Information Collection Activities; Proposals, Submissions, and Approvals: Impact Aid Program Application for Section 8003 Assistance, 57135 2013-22506 Meetings:
National Board for Education Sciences, 57136-57137 2013-22615 President's Board of Advisors on Historically Black Colleges and Universities, 57135-57136 2013-22580 Energy Department Energy Department See Energy Efficiency and Renewable Energy Office See Federal Energy Regulatory Commission Energy Efficiency Energy Efficiency and Renewable Energy Office NOTICES Energy Efficiency Program for Industrial Equipment: UL Verification Services Inc.; Determination Classifying as Nationally Recognized Certification Program for Small Electric Motors, 57137-57139 2013-22569 Waivers:
Panasonic Appliances Refrigeration Systems Corp. of America; Residential Refrigerator and Refrigerator-Freezer Test Procedures, 57139-57141 2013-22582 Samsung Electronics America, Inc.; Residential Refrigerator and Refrigerator-Freezer Test Procedures, 57141-57145 2013-22558 Environmental Protection Environmental Protection Agency RULES Air Quality State Implementation Plans; Approvals and Promulgations: Washington; Puget Sound Clean Air Agency Regulatory Updates, 57073-57075 2013-22478 NOTICES Agency Information Collection Activities;
Proposals, Submissions, and Approvals, 57150-57153 2013-22627 Agency Information Collection Activities; Proposals, Submissions, and Approvals: NOx Budget Trading Program to Reduce Regional Transport of Ozone, 57153-57154 2013-22602 Executive Office of the President See Presidential Documents Federal Aviation Federal Aviation Administration RULES Airworthiness Directives: Eurocopter France Helicopters, 57047-57049 2013-22295 The Boeing Company Airplanes, 57049-57057 2013-22408 2013-22414 PROPOSED RULES Airworthiness Directives:
Diamond Aircraft Industries Airplanes, 57104-57105 2013-22570 NOTICES Passenger Facility Charge Approvals and Disapprovals, 2013-22557 2013-22559 2013-22562 2013-22563 57205-57215 2013-22564 2013-22565 Waivers of Claims Agreements: Orbital Sciences Corp., 57215-57216 2013-22566 Federal Energy Federal Energy Regulatory Commission NOTICES Combined Filings, 57145-57148 2013-22518 2013-22519 2013-22524 Initiation of Proceeding and Refund Effective Date: Midcontinent Independent System Operator, Inc., 57149 2013-22520 Preliminary Permit Applications:
Western Minnesota Municipal Power Agency; Lock+ Hydro Friends Fund III, LLC, 57149 2013-22576 Federal Reserve Federal Reserve System NOTICES Formations of, Acquisitions by, and Mergers of Bank Holding Companies, 57154 2013-22595 Federal Retirement Federal Retirement Thrift Investment Board NOTICES Meetings; Sunshine Act, 57154 2013-22667 Federal Trade Federal Trade Commission NOTICES Granting of Request for Early Termination of the Waiting Period under the Premerger Notification Rules, 57154-57156 2013-22333 Fish Fish and Wildlife Service RULES Endangered and Threatened Wildlife and Plants:
Endangered Status for the Neosho Mucket and Threatened Status for the Rabbitsfoot, 57076-57097 2013-22245 NOTICES Endangered and Threatened Wildlife and Plants Recovery Permit Applications, 57170-57171 2013-22550 Environmental Impact Statements; Availability, etc.: Experimental Removal of Barred Owls to Benefit Threatened Northern Spotted Owls, 57171-57173 2013-22556 Food and Drug Food and Drug Administration RULES Oral Dosage Form New Animal Drugs: Amprolium; Meloxicam, 57057-57058 2013-22523 PROPOSED RULES Color Additive Petitions:
Wm. Wrigley Jr. Co., 57105-57106 2013-22522 NOTICES Agency Information Collection Activities; Proposals, Submissions, and Approvals: Applications for Approval to Market a New Drug; Patent Submission and Listing Requirements, 57164-57166 2013-22540 Meetings: Antiviral Drugs Advisory Committee, 57166 2013-22546 Food and Nutrition Food and Nutrition Service NOTICES Agency Information Collection Activities; Proposals, Submissions, and Approvals: Supplemental Nutrition Assistance Program, 57127-57128 2013-22572 Forest Forest Service NOTICES Meetings:
Forest Resource Coordinating Committee, 57128 2013-22525 General Services General Services Administration NOTICES Agency Information Collection Activities; Proposals, Submissions, and Approvals: Acquisition Regulation; Modifications (Federal Supply Schedules), 57156-57157 2013-22526 Health and Human Health and Human Services Department See Agency for Healthcare Research and Quality See Centers for Disease Control and Prevention See Centers for Medicare & Medicaid Services See Food and Drug Administration See National Institutes of Health Healthcare Research and Quality Agency See Agency for Healthcare Research and Quality Homeland Homeland Security Department See Coast Guard Housing Housing and Urban Development Department RULES Federal Housing Administration Approval of Lending Institutions and Mortgagees:
Streamlined Reporting Requirements for Small Supervised Lenders and Mortgagees, 57058-57061 2013-22583 Interior Interior Department See Fish and Wildlife Service See Land Management Bureau Internal Revenue Internal Revenue Service NOTICES Agency Information Collection Activities; Proposals, Submissions, and Approvals, 2013-22530 57218-57221 2013-22531 2013-22532 2013-22533 2013-22534 International Trade Adm International Trade Administration NOTICES Antidumping and Countervailing Duty Orders;
Results, Extensions, Amendments, etc.: Pasta from Italy and Turkey, 57129-57130 2013-22465 International Trade Com International Trade Commission NOTICES Agency Information Collection Activities; Proposals, Submissions, and Approvals: Digital Trade in the U.S. and Global Economies, Part 2, 57174 2013-22545 Joint Joint Board for Enrollment of Actuaries NOTICES Meetings: Advisory Committee on Actuarial Examinations, 57174-57175 2013-22529 Justice Department Justice Department See Drug Enforcement Administration See Justice Programs Office NOTICES Consent Decrees under the Clean Air Act, 57175 2013-22591 Proposed Consent Decrees under CERCLA, 57175-57176 2013-22567 Proposed Consent Decrees under the Clean Water Act, 57176 2013-22589 Justice Programs Justice Programs Office NOTICES Meetings:
Global Justice Information Sharing Initiative Federal Advisory Committee, 57178 2013-22604 Science Advisory Board, 57177 2013-22628 Land Land Management Bureau NOTICES Records of Decision: Mohave County Wind Farm Project, Mohave County, AZ, 57173-57174 2013-22575 Legal Legal Services Corporation NOTICES Meetings; Sunshine Act, 57178 2013-22666 NASA National Aeronautics and Space Administration NOTICES Meetings: Applied Sciences Advisory Committee, 57178-57179 2013-22594 National Archives National Archives and Records Administration NOTICES Records Schedules, 57179-57180 2013-22544 National Highway National Highway Traffic Safety Administration NOTICES Petitions for Decisions of Inconsequential Noncompliance:
General Motors, LLC, 57216-57218 2013-22561 National Institute National Institutes of Health NOTICES Meetings: Center for Scientific Review, 2013-22492 57168-57170 2013-22503 National Heart, Lung, and Blood Institute, 57168 2013-22504 National Institute on Aging, 57167 2013-22491 National Institute on Deafness and Other Communication Disorders, 57167-57168 2013-22493 National Institute on Drug Abuse, 57166-57167 2013-22502 National Oceanic National Oceanic and Atmospheric Administration RULES Fisheries of the Exclusive Economic Zone Off Alaska:
Pollock in Statistical Area 620 in the Gulf of Alaska; Closure, 57097 2013-22588 Sharks in the Bering Sea and Aleutian Islands Management Area; Closure, 57097-57098 2013-22585 PROPOSED RULES Fisheries of the Exclusive Economic Zone Off Alaska: Groundfish of the Gulf of Alaska; Amendment 95 to the Fishery Management Plan for Groundfish, 57106-57126 2013-22362 NOTICES Agency Information Collection Activities; Proposals, Submissions, and Approvals: Conflict of Interest Disclosure for Nonfederal Government Individuals Who Are Candidates to Conduct Peer Reviews, 57130-57131 2013-22514 Membership of the NOAA Performance Review Board, 57131-57132 2013-22538 Permits:
Endangered Species; File No. 16230, 57132-57133 2013-22592 Marine Mammals; File No. 14514, 57133 2013-22537 National Science National Science Foundation NOTICES Antarctic Conservation Act Permit Applications, 57180 2013-22568 Nuclear Regulatory Nuclear Regulatory Commission NOTICES Facility Operating and Combined Licenses: Applications and Amendments Involving No Significant Hazards Considerations, 57180-57186 2013-22469 Presidential Documents Presidential Documents ADMINISTRATIVE ORDERS Trading With the Enemy Act;
Continuation of Certain Authorities (Presidential Determination) No. 2013-13 of September 12, 2013, 57223-57225 2013-22758 Securities Securities and Exchange Commission NOTICES Self-Regulatory Organizations; Proposed Rule Changes: BOX Options Exchange, LLC, 57191-57195 2013-22509 C2 Options Exchange, Inc, 57195-57198 2013-22510 NASDAQ OMX PHLX, LLC, 57203-57205 2013-22511 NYSE Arca, Inc., 57186-57191 2013-22512 NYSE MKT, LLC, 57198-57203 2013-22513 Transportation Department Transportation Department See Federal Aviation Administration See National Highway Traffic Safety Administration Treasury Treasury Department See Internal Revenue Service See United States Mint U.S.
Mint United States Mint NOTICES Meetings: Citizens Coinage Advisory Committee, 57221 2013-22527 Veteran Affairs Veterans Affairs Department RULES Vet Center Services, 57067-57073 2013-22607 Separate Parts In This Issue Part II Presidential Documents, 57223-57225 2013-22758 Reader Aids Consult the Reader Aids section at the end of this page for phone numbers, online resources, finding aids, reminders, and notice of recently enacted public laws. To subscribe to the Federal Register Table of Contents LISTSERV electronic mailing list, go to http://listserv.access.gpo.gov and select Online mailing list archives, FEDREGTOC-L, Join or leave the list (or change settings); then follow the instructions. 78 180 Tuesday, September 17, 2013 Rules and Regulations DEPARTMENT OF AGRICULTURE Agricultural Marketing Service 7 CFR Part 42 [Doc.
No. AMS-FV-08-0027; FV-05-332] RIN 0581-AC52 United States Standards for Condition of Food Containers AGENCY: Agricultural Marketing Service, USDA. ACTION: Final rule. SUMMARY: The Agricultural Marketing Service
(AMS)is amending the regulations governing the United States (U.S.) Standards for Condition of Food Containers. The revisions to existing tables, removal of operating characteristic
(OC)curves and updating language in the standards would enable the standards to be applicable to most types of food containers and align the standards to reflect current industry practices. DATES: *Effective Date:* October 17, 2013. FOR FURTHER INFORMATION CONTACT: Lynne Yedinak, Specialty Crops Inspection Division, Fruit and Vegetable Program, Agricultural Marketing Service, U.S. Department of Agriculture, 1400 Independence Avenue SW., Room 1536, South Building, Stop 0240, Washington, DC 20250-0240; Telephone:
(202)720-5021, FAX:
(202)690-1527; or email *CIDS@ams.usda.gov* . SUPPLEMENTARY INFORMATION: Executive Order 12866 This final rule has been determined to be not significant for purposes of Executive Order 12866 and therefore, has not been reviewed by the Office of Management and Budget. Regulatory Flexibility Act and Paperwork Reduction Act Pursuant to requirements set forth in the Regulatory Flexibility Act
(RFA)(5 U.S.C. 601-612), AMS has considered the economic impact of this action on small entities. Accordingly, AMS has prepared this final regulatory flexibility analysis. The purpose of the RFA is to fit regulatory action to the scale of business subject to such actions so that small businesses will not be unduly or disproportionately burdened. Food manufacturers are determined to be small businesses in accordance with the Small Business Size Standards by North American Industry Classification Systems (NAICS) codes in Title 13, Code of Federal Regulations
(CFR)13 CFR part 121. These businesses may have fewer than 500, 750, or 1,000 employees depending on their NAICS code. There are approximately 22,058 establishments identified in the 2007 Economic Census as belonging to the North American Industry Classification System under the classification of “food manufacturing” and any number of these establishments could request their product containers be inspected under the provisions of the U.S. Standards for Condition of Food Containers. Only 402 of these establishments would qualify as small businesses under the definition provided by the Small Business Administration. Under the final rule, utilization of the U.S. Standards for Condition of Food Containers continues to be voluntary. We have examined the economic implications of this final rule on small entities. Small entities would only incur direct costs when purchasers of their packaged food products stipulate in their procurement documents that the food containers should conform to the requirements of the U.S. Standards for Condition of Food Containers. Since the standards were last amended in May 1983, innovations in packaging technologies have provided an increasingly wide variety of acceptable new food containers. Accordingly, we believe that the economic impact of this final rule will be minimal because the revisions are necessary in order to provide standards that reflect current industry practices. The changes concerning removal of OC curves and other non-substantive changes will have no adverse impact on small or large entities. The revisions made herein enable the standards to be applicable to most types of food containers and align the standards to reflect current industry practices. With regard to alternatives, this action reflects revisions proposed to the standards as a result of the second proposed rule published in the **Federal Register** , January 18, 2012 [77 FR 2481]. This rule will not impose any additional reporting or recordkeeping requirements on either small or large establishments under the Paperwork Reduction Act, (44 U.S.C. chapter 35). The Department has not identified any relevant Federal rules that duplicate, overlap, or conflict with the Standards. AMS is committed to complying with the E-Government Act of 2002 (44 U.S.C. 3601-3606; 3541-3549), to promote the use of the Internet and other information technologies to provide increased opportunities for citizen access to Government information and services, and for other purposes. Executive Order 12988 This rule has been reviewed under Executive Order 12988, Civil Justice Reform. This action is not retroactive. There are no administrative procedures which must be exhausted prior to any judicial challenge to the provisions of this rule. Background The U.S. Standards for Condition of Food Containers (Standards) currently provides sampling procedures and acceptance criteria for the inspection of stationary lots of filled food containers, which includes skip lot sampling and inspection procedures. It also provides on-line sampling and inspection procedures for food containers during production. Stationary lot sampling is the process of randomly selecting sample units from a lot whose production has been completed. This type of lot is usually stored in a warehouse or in some other storage facility and is offered for inspection. Skip lot sampling is a special procedure for inspecting stationary lots in which only a fraction of the submitted lots are inspected. Skip lot inspection can only be instituted when a certain number of lots of essentially the same quality have been consecutively accepted. To be acceptable under the examination criteria in the standards, lots may contain only a limited number of defects classified as minor, major, or critical. Acceptance criteria are based on sampling plans for different lot sizes and levels of inspection such as normal, reduced, or tightened. Defect tables classify the severity of defects. On-line sampling and inspection is a procedure in which subgroups of sample units or individual containers are selected randomly from pre-designated portions of production. The acceptability of these portions of production is determined by inspecting, at the time of sampling, the subgroups which represent these portions. For this type of sampling, only portions of a lot, rather than a whole lot, may be rejected. This helps to identify trouble spots in a production cycle quickly, and enables the producer to make timely corrections. This can reduce the corrective action costs and the amount of product destroyed as a result of packaging problems. These standards were developed for use by Government agencies when requested to certify filled primary containers or shipping cases, or both, for condition. The standards are permissive, and they may be used in their entirety or in part by private parties. Revision of the Standards includes:
(1)separating Tables I, I-A, II, II-A, III, III-A, and III-B of sampling plans for normal, tightened, and reduced inspection by the type of sampling plan used (single or double), as well as updating the Acceptable Quality Levels
(AQLs)for these tables
(2)updating Table IV—Metal Containers, (Rigid and Semi-Rigid), Table VI—Glass Containers, Table VIII—Rigid and Semi-Rigid Containers (Corrugated or Solid Fiberboard, Chipboard, Wood, Paperboard Aseptic Cartons, Polymeric Trays, etc.), Table IX—Flexible Containers (Plastic Bags, Cello, Paper, Textile, Laminated Multi-Layer Pouch, Bag, etc.), and Table XI—Defects of Label, Marking, or Code to incorporate new defects and revise existing defects to reflect new packaging technologies such as aseptic packaging, metal cans with easy open lids, and plastic rings that hold several containers together
(3)adding new defect tables, Table V—Composite Containers (Semi-Rigid Laminated or Multi-Layer Paperboard Body with Metal, Plastic, or Combination of Metal and Plastic Ends and a Safety Seal Inside the Cap), Table VII—Plastic Containers (Rigid and Semi-Rigid Bottles, Jars, Tubs, Trays, Pails, etc.), and Table XII—Interior Can Defects (a new section 42.114 is added to provide for procedures for evaluating interior container defects)
(4)removing the OC curves
(5)other minor non-substantive changes to clarify the text. These revisions to existing tables, addition of new tables, removal of OC curves, and updating language in the U.S. Standards for Condition of Food Containers enables the standards to be applicable to most types of food containers and align the standards to reflect current industry practices. OC curves found in §§ 42.140, 42.141, 42.142, and 42.143 from Subpart E—Miscellaneous, are removed. This final rule reflects the amendatory language removing these provisions that first appeared in the proposed rule published in the November 19, 2009, **Federal Register** . While these curves show the ability of the various sampling plans to distinguish between accepted and rejected lots, it is our experience that the inclusion of these curves is not critical to use of the standards. Furthermore, they are readily available in literature and on the Internet. Also, Standards for sampling plans including OC Curves are currently available in 7 CFR Part 43. Comments AMS published two proposed rules in the **Federal Register** in which six comments were received. The first proposed rule was published in the **Federal Register** on November 19, 2009 [74 FR 59920], with a sixty-day comment period which closed on January 19, 2010. Two comments were received. One commenter provided a comment that was determined to be outside the scope of the rule. Therefore, no changes were made based on this comment. The other commenter supported the proposed rule revision and provided statements regarding § 42.112—Defects of Containers. The commenter stated that while Table IV of § 42.112 has defects for composite cans listed as a subset of the metal can defects, composite cans also exhibit defects listed in Table VI—Rigid and Semi-rigid containers. The commenter proposed a separate table be added for composite cans extracting the composite can defects from Table IV and Table VI. Based on this comment, AMS added a new Table V that contained the information for composite can defects from Table IV and Table VI and removed the composite information in Table IV. The proposed rule was then reissued. The second proposed rule was published in the **Federal Register** on January 18, 2012 [77 FR 2481] and provided a comment period of sixty days which closed on March 19, 2012. Four comments were received. Two commenters provided comments that were determined to be outside the scope of the rule. Therefore, no changes were made based on those comments. The third commenter supported the revision of the proposed rule with several changes. Comments were received regarding:
(1)the new proposed paragraph § 42.114—Procedures for Evaluating Interior Container Defects and Table XII—Interior Container Defects, and
(2)the proposed modifications to two defects in Table IV—Metal Containers (Rigid and Semi-rigid). Comments received regarding Procedures for Evaluating Interior Container Defects stated that the last four defects in Table XII were vague and not defined. AMS determined the comment had merit and removed major defect 104 and minor defect 204, and revised major defect 105 and minor defect 205 to provide examples of what “other anomaly(ies)” are. The defects were then renumbered. In subsequent discussions, the commenter requested AMS change “Enamel cracked in metal container material not affecting usability” in minor defect 203, Table XII, to “Enamel breakdown in metal affecting usability” as the terms “cracked” and “breakdown” mean the same thing. AMS determined that this had merit and made the change. The commenter also provided comments on § 42.112—Defects of Containers, Table IV—Rigid and Semi-Rigid Containers. The comment concerned major defect 107 for “Metal pop-top:
(b)Missing or incomplete score line:” and minor defect 203 for “Flexible pop-top:
(b)Short pull tab.” The commenter stated that sometimes product design standards request a partial score for a metal pop-top or a shortened pull tab for a flexible pop-top. The commenter requested that AMS revise the defect descriptions to specify that these will not be considered defects when they are requested in a product specification. AMS determined the comment had merit and, to account for this exception, added the phrase “(not conforming to a relevant product specification)” to major defect 107 and minor defect 203. The fourth commenter stated that using “Tetra Pak” is a reference to a company and not the actual type of packaging. The commenter recommended that AMS use one of the specific package trademarks or use the term “Tetra Pak cartons.” AMS determined the comment had merit. AMS has revised the package identification from “Tetra Pak” to “Paperboard Aseptic Cartons” to accurately identify all packaging made in a similar manner. Based on the comments received and information gathered, AMS believes that revising these standards will bring the Standards inline to reflect current industry practices. List of Subjects in 7 CFR Part 42 Food packaging, reporting and recordkeeping requirements. For the reasons set forth in the preamble, 7 CFR part 42 is amended as follows: PART 42—[Amended] 1. The authority citation for part 42 continues to read as follows: Authority: Secs. 203, 205, 60 Stat. 1087, as amended, 1090, as amended (7 U.S.C. 1622, 1624). 2. Section 42.102 is amended by: a. Removing the definitions “Lot”, “Operating Characteristic Curve (OC Curve)” and *“* Probability of acceptance”. b. Revising the definitions “Administrator,” “Sample size (n),” and “Stationary lot sampling” c. Adding the definition “Lot or inspection lot” in alphabetical order. The revisions and addition read as follows: § 42.102 Definitions, general. *Administrator.* The Administrator of the Agricultural Marketing Service
(AMS)of the Department or any other officer or employee of the Agency who is delegated, or who may be delegated the authority to act in the Administrator's stead. *Lot or inspection lot.* A collection of filled food containers of the same size, type, and style. The term shall mean “inspection lot,” i.e., a collection of units of product from which a sample is to be drawn and inspected to determine conformance with the applicable acceptance criteria. An inspection lot may differ from a collection of units designated as a lot for other purposes (e.g., production lot, shipping lot, etc.). *Sample size (n).* The number of sample units included in the sample. *Stationary lot sampling.* The process of randomly selecting sample units from a lot whose production has been completed. This type of lot is usually stored in a warehouse or in some other storage facility and is offered in its entirety for inspection. § 42.106 [Amended] 3. In § 42.106, paragraph (a)(1), remove the word “attributed” and add in its place the word “attributed”. 4. Revise § 42.109, to read as follows: § 42.109 Sampling plans for normal condition of container inspection, Tables I and I-A. Table I—Single Sampling Plans for Normal Condition of Container Inspection Code Lot size ranges— Number of containers in lot Type of Plan Acceptable quality levels Origin Inspection Sample size 0.25 Ac Re 1.5 Ac Re 6.5 Ac Re Other Than Origin Inspection 0.25 Ac Re 2.5 Ac Re 10.0 Ac Re CA 6,000 or less Single 84 0 1 3 4 9 10 0 1 4 5 13 14 CB 6,001-12,000 Single 168 1 2 5 6 16 17 1 2 7 8 23 24 CC 12,001-36,000 Single 315 2 3 8 9 28 29 2 3 13 14 41 42 CD Over 36,000 Single 500 3 4 12 13 42 43 3 4 18 19 62 63 CE Single 800 4 5 18 19 64 65 4 5 27 28 95 96 Ac = Acceptance number. Re = Rejection number. ER17SE13.004 5. Revise § 42.110 to read as follows: § 42.110 Sampling plans for tightened condition of container inspection; Tables II and II-A. Table II—Single Sampling Plans for Tightened Condition of Container Inspection Code Lot size ranges— Number of containers in lot Type of Plan Acceptable quality levels Origin Inspection Sample Size 0.25 Ac Re 1.5 Ac Re 6.5 Ac Re Other Than Origin Inspection 0.25 Ac Re 2.5 Ac Re 10.0 Ac Re CB 6,000 or less Single 168 0 1 4 5 11 12 0 1 5 6 16 17 CC 6,001-12,000 Single 315 1 2 6 7 19 20 1 2 8 9 28 29 CD 12,001-36,000 Single 500 2 3 9 10 28 29 2 3 12 13 42 43 CE Over 36,000 Single 800 3 4 13 14 42 43 3 4 18 19 64 65 CF Single 1,250 4 5 19 20 63 64 4 5 26 27 96 97 ER17SE13.005 6. Revise § 42.111 to read as follows: § 42.111 Sampling plans for reduced condition of container inspection, Tables III and III-A; and limit number for reduced inspection, Table III-B. Table III—Single Sampling Plans for Reduced Condition of Container Inspection Code Lot size ranges— Number of containers in lot Type of Plan Acceptable quality levels Origin inspection Sample Size 0.25 Ac Re 1.5 Ac Re 6.5 Ac Re Other Than Origin Inspection 0.25 Ac Re 2.5 Ac Re 10.0 Ac Re CAA 6,000 or less Single 29 1 2 1 2 4 5 1 2 2 3 5 6 CA 6,001-36,000 Single 84 1 2 3 4 9 10 1 2 4 5 13 14 CB Over 36,000 Single 168 1 2 5 6 16 17 1 2 7 8 23 24 CC Single 315 2 3 8 9 28 29 2 3 13 14 41 42 ER17SE13.006 Table III-B—Limit Numbers for Reduced Inspection Number of sample units from last 10 lots inspected within 6 months Acceptable quality level 0.25 1.5 2.5 6.5 10.0 320-499 (*) 1 4 14 24 500-799 (*) 3 7 25 40 800-1,249 0 7 14 42 68 1,250-1,999 0 13 24 69 110 2,000-3,149 2 22 40 115 181 3,150-4,999 4 38 67 186 293 5,000-7,999 7 63 110 302 472 8,000-12,499 14 105 181 491 765 12,500-19,999 24 169 290 777 1207 * Denotes that the number of sample units from the last 10 inspection lots is not sufficient for reduced inspection for this AQL. In this instance more than 10 inspection lots may be used for the calculations if; the inspection lots used are the most recent ones in sequence within the last 6 months, they have all been on normal inspection, and none has been rejected on original inspection. 7. Section § 42.112 is revised to read as follows: § 42.112 Defects of containers: Tables IV, V, VI, VII, VIII, IX, and X. Table IV—Metal Containers [Rigid and semi-rigid] Defects Categories Critical Major Minor Type or size of container or component parts not as specified None permitted Closure incomplete, not located correctly or not sealed, crimped, or fitted properly:
(a)Heat processed primary container 1
(b)Non-heat processed primary container 101
(c)Other than primary container 201 Dirty, stained, or smeared container 202 Key opening metal containers (when required):
(a)Key missing 102
(b)Key does not fit tab 103
(c)Tab of opening band insufficient to provide accessibility to key 104
(d)Improper scoring (band would not be removed in one continuous strip) 105 Metal pop-top:
(a)Missing or broken pull tab 106
(b)Missing or incomplete score line (not conforming to a relevant product specification) 107 Flexible pop-top:
(a)Poor seal (wrinkle, entrapped matter, etc.) 108
(b)Short pull tab (not conforming to a relevant product specification) 203
(c)Missing pull tab 109
(d)Torn pull tab 204 Open top with plastic overcap (when required):
(a)Plastic overcap missing 110
(b)Plastic overcap warped (making opening or reapplication difficult) 111 Outside tinplate or coating (when required):
(a)Missing or incomplete 205
(b)Blistered, flaked, sagged, or wrinkled 206
(c)Scratched or scored 207
(d)Fine cracks 208 Rust (rust stain confined to the top or bottom double seam or rust that can be removed with a soft cloth is not scored a defect):
(a)Rust stain 209
(b)Pitted rust 112 Wet cans (excluding refrigerated containers) 210 Dent:
(a)Materially affecting appearance but not usability 211
(b)Materially affecting usability 113 Buckle:
(a)Not involving end seam 212
(b)Extending into the end seam 114 Collapsed container 115 Paneled side materially affecting appearance but not usability 213 Solder missing when required 116 Cable cut exposing seam 117 Improper side seam 118 Swell, springer, or flipper (not applicable to gas or pressure packed product nor frozen products) 2 Leaker or blown container 3 Frozen products only:
(a)Bulging ends 3/16 -inch to 1/4 -inch beyond lip 214
(b)Bulging ends more than 1/4 -inch beyond lip 119 Metal drums: leaking filling seal
(bung)swell 1 4 120 1 Defect classification depends on the severity of the defect. Table V—Composite Containers [Fiberboard body with metal lids or metal bottoms, plastic or foil top with cap] Defects Categories Critical Major Minor Type or size of container or component parts not as specified None permitted Closure incomplete, not located correctly or not sealed, crimped, or fitted properly 1 Dirty, stained, or smeared container 201 Easy open closure:
(a)Pull tab: 1. Missing or broken pull tab 101 2. Missing or incomplete score line 102
(b)Membrane top: 1. Poor seal (wrinkle, entrapped matter, etc.) 103 2. Short pull tab 104 3. Missing pull tab 105 4. Torn pull tab 106
(c)Open top with plastic overcap (when required): 1. Plastic overcap missing 107 2. Plastic overcap warped (making opening or reapplication difficult) 108 Outside tinplate or coating on ends (when required):
(a)Missing or incomplete 202
(b)Blistered, flaked, sagged, or wrinkled 203
(c)Scratched or scored 204
(d)Fine cracks 205 Collapsed container 109 Paneled side materially affecting appearance but not usability 206 Leaker 2 Wet or damp:
(a)Materially affecting appearance but not usability 207
(b)Materially affecting usability 110 Crushed or torn area:
(a)Materially affecting appearance but not usability 208
(b)Materially affecting usability 111 Table VI—Glass Containers [Bottles, Jars] Defects Categories Critical Major Minor Type or size of container or component parts not as specified None permitted Closure not sealed, crimped, or fitted properly:
(a)Heat processed 1
(b)Non-heat processed 101 Dirty, stained, or smeared container 201 Chip in glass 202 Stone (unmelted material) in glass 203 Pits in surface of glass 204 Sagging surface 205 Bead (bubble within glass):
(a)1/8 -inch to 1/16 -inch in diameter 206
(b)Exceeding 1/8 -inch in diameter 102 Checked 103 Thin spot in glass 104 Blister (structural defect) 105 Bird swing (glass appendage inside container) 2 Broken or leaking container 3 Cap (nonheat processed):
(a)Cross-threaded 207
(b)Loose but not leaking 208
(c)Pitted rust 106 Cap (heat processed):
(a)Cross-threaded or loose 4
(b)Pitted rust 107 Sealing tape or cello band (when required):
(a)Improperly placed 209
(b)Not covering juncture of cap and glass 108
(c)Ends overlap by less than 1/2 -inch 109
(d)Loose or deteriorating 110 Missing or torn outer safety seal 111 Inner safety seal—missing, torn, poor seal 112 Table VII—Plastic Containers [Rigid and Semi-Rigid, Bottles, Jars, Tubs, Trays, Pails, etc.] Defects Categories Critical Major Minor Type or size of container or component parts not as specified None permitted Closure not sealed, crimped, or fitted properly:
(a)Heat processed 1
(b)Non-heat processed 101 Dirty, stained, or smeared container 201 Chip in plastic 202 Un-melted gels in plastic 203 Pits in surface of plastic 204 Sagging surface 205 Air bubble within plastic:
(a)1/8 -inch to 1/16 -inch in diameter 206
(b)Exceeding 1/8 -inch in diameter 102 Checked 103 Thin spot in plastic 104 Blister (structural defect) 105 Broken or leaking container 2 Cap (non-heat processed):
(a)Cross-threaded 207
(b)Loose but not leaking 208 Cap (heat processed), cross-threaded or loose 3 Security seals:
(a)Closure ring missing 106
(b)Missing or torn outer safety seal 107
(c)Inner safety seal—missing, torn, or poor seal 108
(d)Sealing tape or cello band (when required): 1. Improperly placed 209 2. Not covering juncture of cap and plastic 109 3. Ends overlap by less than 1/2 -inch 110 4. Loose or deteriorating 111 Table VIII—Rigid and Semi-Rigid Containers—Corrugated or Solid Fiberboard, Chipboard, Wood, Paperboard Aseptic Cartons, Polymeric Trays, etc. [Excluding metal, glass, and plastic] Defects Categories Critical Major Minor Type or size of container or component parts not as specified None permitted Component part missing 101 Closure not sealed, crimped, or fitted properly:
(a)Primary container 1
(b)Other than primary container 201 Dirty, stained, or smeared container 202 Wet or damp (excluding ice packs):
(a)Materially affecting appearance but not usability 203
(b)Materially affecting usability 102 Moldy area 2 Crushed or torn area:
(a)Materially affecting appearance but not usability 204
(b)Materially affecting usability 103 Separation of lamination (corrugated fiberboard):
(a)Materially affecting appearance but not usability 205
(b)Materially affecting usability 104 Product sifting or leaking 105 Nails or staples (when required):
(a)Not as required, insufficient number or improperly positioned 206
(b)Nails or staples protruding 106 Glue or adhesive (when required); not holding properly, not covering area specified, or not covering sufficient area to hold properly:
(a)Primary container 107
(b)Other than primary container 207 Flap:
(a)Projects beyond edge of container more than 1/4 -inch 208
(b)Does not meet properly, allowing space of more than 1/4 -inch 209 Sealing tape or strapping (when required):
(a)Missing 108
(b)Improperly placed or applied 210 Missing component (straw, etc.) 211 Paperboard Aseptic Cartons:
(a)Missing re-sealable cap or tab 109
(b)Inner or outer safety seal—missing, torn, poor seal 3 Thermostabilized polymeric trays: Tray body:
(a)Swollen container 4
(b)Tear, crack, hole, abrasion through more than one layer of multi-layer laminate for the tray 5
(c)Presence of delamination in multi-layered laminate 212
(d)Presence of any permanent deformation, such that deformed area is discolored or roughened in texture 213 Lid material:
(a)Closure seal not continuous along tray flange surface 6
(b)Foldover wrinkle in seal area extends into the closure seal such that the closure seal is reduced to less than 1/8 -inch 7
(c)Any impression or design on the seal surfaces which conceals or impairs visual detection of seal defects 110
(d)Areas of “wave-like” striations or wrinkles along the seal area that spans the entire width of seal 214
(e)Abrasion of lid material: 1. Within 1/16 -inch of food product edge of seal such that barrier layer is exposed 8 2. Greater than 1/16 -inch from food product edge of seal that barrier layer is exposed 215
(f)Presence of entrapped matter within 1/16 -inch of the food product edge of seal or entrapped moisture or vapor with 1/16 -inch of the food product edge of seal that results in less than 1/16 -inch of defect free seal width at the outside edge 9
(g)Presence of any seal defect or anomaly (for example, entrapped moisture, gases, etc.) within 1/16 -inch of food product edge of seal 111
(h)Closure seal width less than 1/8 -inch 216 Table IX—Flexible Containers [Plastic, Cellophane, Paper, Textile, Laminated Multi-Layer Pouch, Bag, etc.] Defects Categories Critical Major Minor Type or size of container or component parts not as specified None permitted Closure not sealed, crimped, stitched, or fitted properly:
(a)Heat processed primary container 1
(b)Non-heat processed primary container 101
(c)Other than primary container 201 Dirty, stained, or smeared container 202 Unmelted gels in plastic 203 Torn or cut container or abrasion (non-leaker):
(a)Materially affecting appearance but not usability 204
(b)Materially affecting usability 102 Moldy area 2 Individual packages sticking together or to shipping case (tear when separated) 103 Not fully covering product 104 Wet or damp (excluding ice packs):
(a)Materially affecting appearance but not usability 205
(b)Materially affecting usability 105 Over wrap (when required):
(a)Missing 106
(b)Loose, not sealed, or closed 206
(c)Improperly applied 207 Sealing tape, strapping, or adhesives (when required):
(a)Missing 107
(b)Improperly placed, applied, torn, or wrinkled 208 Tape over bottom and top closures (when required):
(a)Not covering stitching 108
(b)Torn (exposing stitching) 109
(c)Wrinkled (exposing stitching) 110
(d)Not adhering to bag: 1. Exposing stitching 111 2. Not exposing stitching 209
(e)Improper placement 210 Product sifting or leaking:
(a)Non-heat processed 112
(b)Heat processed 3 Flexible pop-top:
(a)Poor seal (wrinkle, entrapped matter, etc.) reducing intact seal to less than 1/16 -inch 4
(b)Short pull tab (materially affecting usability) 212
(c)Missing pull tab 113
(d)Torn pull tab (materially affecting usability) 213 Missing component (straw, etc.) 214 Two part container (poly lined box or bag in box):
(a)Outer case torn 215
(b)Poly liner: 1. Missing 5 2. Improper closure 114 Missing “zip lock” (re-sealable containers) 216 Loss of vacuum (in vacuum-packed) 115 Pre-formed containers:
(a)Dented or crushed area 217
(b)Deformed container 218 Missing re-sealable cap 116 Inner or outer safety seal—missing, torn, poor seal 6 Air bubble in plastic 117 Thermostabilized products (includes but not limited to tubes, pouches, etc.): Foldover wrinkle in seal area (thermostabilized pouches):
(a)Extends through all plies across seal area or reduces seal less than 1/16 -inch 7
(b)Does not extend through all plies and effective seal is 1/16 -inch or greater 219 Incomplete seal (thermostabilized pouches) 8 Non-bonding seal (thermostabilized pouches) 9 Laminate separation in body of pouch or in seal within 1/16 -inch of food product edge:
(a)If food contact layer is exposed 10
(b)If food contact surface is exposed after manipulation or laminate separation expands after manipulation 118
(c)If lamination separation is limited to isolated spots that do not propagate with manipulation or is outer ply separation in seal within 1/16 -inch of food product edge of seal 220 Flex cracks (cracks in foil layer only) 221 Swollen container 11 Blister (in seal) reducing intact seal to less than 1/16 -inch 12 Compressed seal (overheated to bubble or expose inner layer) reducing intact seal to less than 1/16 -inch 13 Stringy seal (excessive plastic threads showing at edge of seal area) 222 Contaminated seal (entrapped matter) reducing intact seal to less than 1/16 -inch 14 Seal creep (product in pouch “creeping” into seal) reducing intact seal to less than 1/16 inch 15 Misaligned or crooked seal reducing intact seal to less than 1/16 -inch 16 Seal formed greater than 1-inch from edge of pouch (unclosed edge flaps) 223 Waffling (embossing on surface from retort racks; not scorable unless severe) 224 Poor or missing tear notch (when required) 225 Table X—Unitizing [Plastic or other type of casing/unitizing] Defects Categories Major Minor Not specified method 101 Missing tray (when required) 102 Missing shrink wrap (when required) 103 Loose or improperly applied wrap 201 Torn or mutilated 202 Off-center wrap (does not overlap both ends) 203 8. Section 42.113 is revised to read as follows: § 42.113 Defects of label, marking, or code. Table XI—Label, Marking, or Code Defects Categories Major Minor Not specified method 101 Missing (when required) 102 Loose or improperly applied 201 Torn or mutilated 202 Torn or scratched, obliterating any markings on the label 103 Text illegible or incomplete 203 Incorrect 104 In wrong location 204 9. Add § 42.114 to subpart B to read as follows: § 42.114 Procedures for evaluating interior container defects.
(a)Sections 42.101-42.136 provide procedures for determining lot conformance with the U.S. Standards for Condition of Food Containers. This determination is based on the examination of the external characteristics of the food containers.
(b)As an option, if a user of the inspection service requests to have the interior characteristics of containers examined, and apply these results in the determination of lot acceptability, the defects listed in Table XII may be used.
(c)The determination of lot acceptability based on internal container defects shall be independent of the determination of lot acceptability for U.S. Standards for Condition of Food Containers. A user of the inspection service may choose to require inspection for internal can defects as well as inspection for U.S. Standards for Condition of Food Containers.
(d)If a user of the inspection service requests an examination for internal container defects in addition to an official USDA/USDC inspection for product quality and/or U.S. grade, the containers opened by the official inspection service for inspection of product quality and/or U.S. grade will be used for examination of interior container defects. The minimum sample size for evaluation of interior container defects will be 13 containers. As a result, additional containers will be required if the inspection for quality or U.S. grade calls for fewer than 13 containers. Table XIII provides acceptance numbers for internal container defects for selected sample sizes. Table XII—Interior Container Defects Defects Categories Major Minor De-tinning in metal container materially affecting usability 101 De-tinning in metal container not materially affecting usability 201 Black spots in metal container 202 Enamel missing (when required) in metal container 102 Enamel breakdown in metal container material affecting usability 103 Enamel breakdown in metal container material not affecting usability 203 Other defect(s) of the interior of the container (metal, plastic, paper, rigid, etc.) e.g., interior damage, tear, delamination, missing layer, off-odor, interior blisters, etc. that materially affects usability 104 Defect(s) of the interior of the container (metal, plastic, paper, rigid, etc.) e.g., interior damage, tear, delamination, missing layer, off-odor, interior blisters, etc. that materially affects appearance but not usability 204 Table XIII—Acceptance Numbers for Internal Container Defects Sample Size (n = number of containers) Major Interior Defects Ac Re Total Interior Defects Ac Re n—13 0 1 2 3 n—21 1 2 3 4 n—29 1 2 4 5 n—38 2 3 5 6 n—48 2 3 6 7 n—60 2 3 7 8 Dated: September 11, 2013. Rex A. Barnes, Associate Administrator, Agricultural Marketing Service. [FR Doc. 2013-22574 Filed 9-16-13; 8:45 am]
Connectionstraces to 3
Traces to 3 documents
6 references not yet in our index
- 7 CFR 42
- 5 USC 601-612
- 13 CFR 121
- 44 USC 3601-3606
- 7 CFR 43
- 60 Stat. 1087
Citation graph
cites case law
Unknown
Final rule
Cite7 CFR 42
Cite5 USC 601-612
Cite13 CFR 121
Cite44 USC 3601-3606
Cite7 CFR 43
Cites 9 · showing 8Cited by 0 across 0 sources